Overview Specifications Brochure Technical assistance? Call (+49) 69 1534 3013 MJ6-i Dehumidifying dryer with a honeycomb rotor for stable drying The new MJ6-i is the result of Matsui´s constant striving for high standards in treating polymers. It continuously monitors load demands and dials down energy consumption while keeping resin a consistent -60ºC dew point all the way to its core, drying it in a fast way to allow a faster start of process. Furthermore, the built-in self‑control option embedded in the equipment "i" (for intelligence) avoids that the drying process gets affected by the outside air temperature and humidity. Saving energy, ensuring quality The MJ6-i saves up to 83% energy through the continuous operation method: the resin´s temperature drops after drying and the evolution of air flow rate, preventing excessive drying and yellowing of products. In addition, the regeneration heating air is pre-heated with waste heat, as to reduce the required power consumption. "Honeycomb" dessicant wheel Matsui developed the “honeycomb” desiccant wheel technology, perfecting it throughout four decades. The spinning wheel is constantly presenting fresh, thirsty desiccant as moist air travels through every channel. As the wheel travels, “wet” desiccant is dried and ready to absorb moisture again. Engineered to perform maintenance-free, desiccant wheels routinely can hold dew point to -40ºC for years. Intuitive design of the touch-screen Settings on the new seven-inch touch-screen display present a smoother and simpler design. Thank to this, it´s possible to check the drying status, the machine's operating history, and to change the temperature. In addition it has a range of different languages to choose from. Small unique features Large, easy-access, hopper door Front-of-system access for simple routine maintenance Capture dust with cyclonic filter before it reaches the main filter Easy-clean feed line damper valve MJ6-i Model MJ6-i- 30 50 75 135 Power supply Operation circuit 400V 50Hz 3P Breaker capacity 30A 50A Apparent power 200V 50/60Hz 6.7kVa 7.2kVa 8.2kVa 13.5kVa 220V 60Hz 7.3kVa 7.9kVa 9.1kVa 15.3kVa 230V 60Hz 6.9kVa 7.5kVa 8.8kVa 13.8kVa 380V 50/60Hz 6.5kVa 7kVa 8.1kVa 13.3kVa 400V 50/60Hz 6.8kVa 7.4kVa 8.6kVa 14.2kVa 415V 50/60Hz 7.1kVa 7.7kVa 9kVa 14.9kVa 460V 60Hz 7.3kVa 7.8kVa 9kVa 14.9kVa Air Pressure 0.5 Mpa Flow rate 10L/h Diameter 6mm Operating temperature 70-160°CV Dew-point -40 to -60°C Volume 30kg/50L 50kg/85L 75kg/130L 135kg/225L Drying heater capacity 200V 50/60Hz 2.1kW 2.4kW 5.4kW 220V 60Hz 2.5kW 2.9kW 6.5kW 230V 60Hz 2.3kW 2.6kW 5.4kW9 380V 50/60Hz 2.1kW 2.4kW 5.4kW 400V 50/60Hz 2.3kW 2.7kW 6kW 415V 60Hz 2.5kW 2.9kW 6.4kW 460V 60Hz 2.3kW 2.6kW 5.9kW Conveying blower output 1.1 (50Hz)/1.5 (60Hz) Conveying distance Primary side 10m Secondary side 5m Drying blower 0.28kW 0.42kW 1.15kW Regeneration blower 0.28Kw 0.42Kw Regeneration heater 200V 50/60Hz 1kW 1.5kW 2.1kW 3.1kW 220V 60 Hz 1.2Kw 1.8Kw 2.5kW 3.1kW 230V 60Hz 1kW 1.5kW 2.1kW 3.1kW 380V 50/60 Hz 1Kw 1.5Kw 2.1kW 3.1kW 400V 50/60Hz 1.1kW 1.7kW 2.3kW 3.4kW 415V 50/60Hz 1.2Kw 1.8Kw 2.5kW 3.7kW 460V 60Hz 1.1kW 1.6kW 2.3kW 3.4kW Absorption tower motor control 25w Drying temperature control PID control heater, non-contact relay Regenerational temperature control PID control heater, non-contact relay Schedule timer Set individually in one week (Monday to Sunday) External control (startup) External non-voltage contact (incoming current: 5A) Piping diameter 38mm PVC hose Weight 265kg 275kg 290kg 395kg Alarm or protection cirucit Overheat protection (drying & regeneration temperature), blower overload, drying & regenerating blower reversal prevention. Check out the MJ6-i´s potential!
